Description Accu-Tech original premium 4×2 cleaning cloth for cleaning firearms. It is 4 inches wide with 2 inch red lines to indicate where the cloth should be cut or ripped. About 10 meters in length.

Read more less

Description Moulded in U.V. stabilised polyethylene, this 22.7 litre fuel tank has a direct reading fuel gauge incorporated in the cap, with stainless steel wire and for easy carrying incorporates a handle at one end. Supplied complete with fuel tank pickup with 1⁄4″ BSP internal thread. Fuel tank adaptors are sold separately. Adaptors must be ordered separately to suit the outboard make and are listed on the following pages. BLA CODE HEIGHT MM WIDTH MM LENGTH MM 200110 235 290 590 Accessories 200146 Fuel Cap Warning N.B. There is always an element of risk when carrying fuel. Caution should be exercised when using this equipment

Read more less

Description This rod holder can easily adjust a rod from 5º to 95°. The base design has twelve variable positions to allow the rod to rotate through 360°. Thumb activated, slide locking ring retains the rod when trolling. Supplied with a side mount bracket with channel to allow mounting on rails up to 25mm diameter with optional rail mount adaptor. Various additional mounts can be ordered separately and are listed below. Rod holder and mount kits are all moulded in tough polyethylene

Read more less

Description Polished Stainless steel Rod Holder Angled or Straight Mount Polished stainless steel fabricated construction. 6mm gimbal pin for rod alignment. Angled or straight through deck mount. Intrusion: Straight 197mm; (Angled 188mm) Cut out: 44mm Deck Flange: 80 x 59mm Mount Screws: Use 8g Counter sunk

Read more less

Description Stainless steel fabricated construction with 30° angled deck mount. Protective white PVC liner. 5mm diameter pin in base of tube for rod alignment. Supplied with mount gasket. Deck Plate: 110mm x 87mm Intrusion: 220mm Cut Out: 51mm Mount Screws: 6mm c/s

Read more less

Description Formed from heavy gauge 316 grade stainless steel. Double roller and hinged nose section designed to securely store, as well as automatically deploy the anchor. Spring loaded, quick release captive pin to retain anchor and warp. Overall Length: 355mm Mount Base: 125mm x 57mm Height: 110mm Roller Width: 48mm Mount Screws: 6mm c/s

Read more less

Description Includes a quick release pin. Note taht these are 316 grade stainless steel, most on the market are not. One piece pressed, heavy gauge, 316 grade stainless steel housing. Black delrin roller. Spring loaded, quick release captive pin to retain anchor and warp. Height mm: 73 Mount Screws mm: 6 c/s O/all Length mm: 225 Mount Base mm: 125×57 Roller Width mm: 48

Read more less

Description The Berkley Wall / Ceiling Mount 8 Rod Rack mounts conveniently on the wall or ceiling of your home, garage or cabin and holds rods horizontally with or without reels. It’s made of powder-coated steel that’s durable and long-lasting. Keep your rods off the floor and out of the corner! Berkley Wall / Ceiling Mount 8 Rod Rack Features: Holds up to 8 rods/combos Versatile mounting on the wall / ceiling Powder-coated steel Protective ring to protect rod butt and tip Dimensions: 1000 x 100 x 50mm

Read more less

Description Beach spike 1200mm Long with step NZ Made beach spikes. Made tough for New Zealand conditions Galvanised Steel

Read more less

Description NZ Made Rock spikes. Made tough for New Zealand conditions Galvanised Steel

Read more less

Description NZ Made Rock spikes. Made tough for New Zealand conditions Galvanised Steel

Read more less

Description The Nacsan kayak longline is a 13 hook longline ideal for small boats or kayaks. It includes full length traces trace rack with bracket for rod holder lead filled alloy grapnels 500g with shark clips 6 hard plastic floats with shark clips. Everything is compact and very easy to use.

Read more less

Description NZ Made Rod Racks. Made High density foam with strong Velcro strapping mounted on plastic bases. Ideal for storing rods, gaffs, landing nets, boat hooks, wine glasses, garden tools, poles, horse whips… Adhesive strip can attached to alloy firberglass or any hard smooth clean surface Can accommodate from small to large diameter items. Racks can be attached vertically, horizontally even to the ceiling for storage

Read more less

Description NZ Made Rod Racks. Made High density foam with strong Velcro strapping mounted on plastic bases. Ideal for storing rods, gaffs, landing nets, boat hooks, wine glasses, garden tools, poles, horse whips… Adhesive strip can attached to alloy firberglass or any hard smooth clean surface Can accommodate from small to large diameter items. Racks can be attached vertically, horizontally even to the ceiling for storage

Read more less

Description Rectangular Flush Mount, 57 x 33mm

Read more less

Description Magnetic – Strong Holds Really Well Made in NZ by Nacsan Products Length 350mm Width 50mm Foam Non Scratch Attachments Velcro Locking Tie Downs Included Work Well Full Instructions Included

Read more less

Description The 12 Volt Removable Light Pole has telescopic 360° white riding lights with LED efficiency and durability. Fitted to a light weight aluminium pole with plastic base. Not only are the Fold Down Lights water resistant, they meet US Coast Guards COLREG 4nm A-16. Height: 610mm

Read more less

Description The Digital Voltage Sensing Relay (DVSR) allows the charging of a second battery bank from any single charging source. When the voltage on the charged bank rises sufficiently, the DVSR engages allowing the 2nd battery bank to charge. When charging stops and voltage falls, the DVSR automatically isolates the battery banks, ensuring that engine start batteries are kept fully charged. Digital circuitry provides superior reliability and extremely low power consumption. Digital enhancements have introduced remote sensing circuitry that allows an optional connection from the ignition switch to provide the same functionality as single sense VSR and zero power consumption when engine is off. Another benefit is a zero stand by current draw when remote sensing circuit is utilized with a storage mode switch fitted (switch in open position). Safely charge two or more independent battery banks from one charge source such as an alternator or battery charger Charges engine starting batteries before combining auxiliary bank for charging Protects start batteries from becoming flattened by domestic loads Isolates electronics from harmful electrical surges from starter motors Simple to install 3 wire connection leaves alternator wiring intact No volt drop vs diode isolators Ignition protected Surface or panel mountable Replaces previous models 710-125A and 710-125A-DS Multi voltage, auto selects between 12 and 24V DC operation Digital circuits provide very low power consumption and enhanced performance Remote status LED output option Continuous rating: 140 Engages: 13.2 VDC, Disengages: 12.7 VDC

Read more less

Description OVERVIEW The SOLIX 10 CHIRP MSI combines cutting-edge technologies like MEGA Side Imaging+, MEGA Down Imaging+, Dual Spectrum CHIRP Sonar and AutoChart Live on an ultra-clear Cross Touch® display. Take full advantage of the generous 10.1″ touchscreen display with customizable views and settings that allow you to see multiple technologies at once and find what you want quickly via the convenient side bar menu. Leverage the networking power of built-in Wi-Fi and NMEA 2000®, as well as Bluetooth® and Ethernet connections for compatibility with the One-Boat Network™ family of products from Humminbird, Minn Kota and Cannon.

Read more less

Description Charge two mobile devices on the go Made with corrosion resistant materials which ensure a solid contact and low voltage drop. Fits in same mounting hole as a traditional 12 Volt outlet Compatible with most mobile devices including Apple® products Protective dust cap with tether keeps dust and spray from shortening the life of the charger Conformal coated circuit board to stand up to the harsh marine environment 2A Supply fuse is not included Easy to install in existing 12V DC socket hole providing convenient access for charging mobile devices Specifications Maximum Output Current 2.1A DC (total) Cut Out Dimensions 1 1⁄8 in (28.58 mm) dia. hole Input Voltage 12V 24V Input Voltage Range 9-32V Output Voltage 5V DC +/- 5% Parasitic Current Draw 15mA Reverse Polarity Protection Yes Short Circuit Protection Yes Thermal Overload Protection Yes USB 2.0 Weight 0.10lb (0.05 kg)

Read more less

Description The RodStow rod holder system is a vertical fishing rod storage rack and caddy for boats. RodStow rod racks will hold your rods above deck, safely and securely, ready for your fishing experience. The RodStow Double is available in black or white, comes with stainless steel fasteners and can be installed in minutes. It features a storage caddy for lures, traces and other tackle, it’s even big enough to hold a small tackle box. These rod holders have a removable gimbal pin that you can leave in to support the rod and stop rotation, or remove to let the rod pass through. RodStow is a modular system, if you buy more you can add them together to make longer rod racks. Offset mounting is possible, giving you a solution for storing larger reels, without them hitting each other. The vertical RodStow rod rack is suitable for most rods and reels, including spinning, trigger, boat and game reels, and any length of fishing rod. Storage caddy for lures, traces and other tackle Tube size 40mm (1.57in) inside diameter Can holds gaffs, boat hooks or nets Removable gimbal pin to stop rod rotation Made from UV Stabilised, fibreglass reinforced engineering polymers Fits all rod lengths Stainless steel screws

Read more less

Description The RodStow rod holder system is a vertical fishing rod storage rack and caddy for boats. RodStow rod racks will hold your rods above deck, safely and securely, ready for your fishing experience. The RodStow Triple is available in black or white, comes with stainless steel fasteners and can be installed in minutes. It features a storage caddy for lures, traces and other tackle, it’s even big enough to hold a small tackle box. These rod holders have a removable gimbal pin that you can leave in to support the rod and stop rotation, or remove to let the rod pass through. RodStow is a modular system, if you buy more you can add them together to make longer rod racks. Offset mounting is possible, giving you a solution for storing larger reels, without them hitting each other. The vertical RodStow rod rack is suitable for most rods and reels, including spinning, trigger, boat and game reels, and any length of fishing rod. Storage caddy for lures, traces and other tackle Tube size 40mm (1.57in) inside diameter Can holds gaffs, boat hooks or nets Removable gimbal pin to stop rod rotation Made from UV Stabilised, fibreglass reinforced engineering polymers Fits all rod lengths Stainless steel screws

Read more less

Description Simrad’s GS25 GPS antenna is the ideal GPS for any navigator that requires extremely accurate and rapid vessel position and speed updates.

Read more less